Bath & Body5 min read

How to Use Avarampoo Flowers: Boil, Strain and Mix

By THENVANAM Editorial · Published 27 September 2026

In short

To use avarampoo flowers: boil a handful of the dried flowers in water for a few minutes, let the water cool, then strain it. Mix the strained water gradually into gram flour or another suitable natural base to make a paste, use it externally as a body or face preparation, and rinse thoroughly. Patch test first and avoid the eyes.

How to Use Avarampoo Flowers: Boil, Strain and Mix

Steps

Boil a handful of flowers
Put a handful of the dried flowers in a small pan with about two cups of water — a starting point, not a fixed measure. Bring it to the boil and let it bubble gently for a few minutes. Use dry hands or a dry spoon to take the flowers from the pack.
Let the water cool
Take the pan off the heat and leave it until the water has cooled completely, or at least to a temperature you would comfortably put on skin. Never mix or apply it hot.
Strain out the flowers
Pour the water through a fine strainer or a clean cotton cloth into a bowl. The spent flowers have done their job — the water is what you use.
Mix into the base, a little at a time
Put about 2 tablespoons of gram flour (or your chosen natural base) into a dry bowl and add the strained water a spoonful at a time, stirring as you go. Stop when you have a smooth paste that holds on a spoon but spreads without dragging. Adjust the amount for the area you plan to cover.
Patch test the first time
Before your first full use, apply a small amount of the paste to a small area of skin, such as the inner forearm, and wait before using it more widely. Test in the same base you intend to use.
Apply externally
Spread an even layer on the body or face, keeping well clear of the eyes. Leave it for around 5–10 minutes as a starting point, and rinse before it dries hard — a fully dried paste flakes and is harder to wash away.
Rinse and clean up
Rinse thoroughly with plain water until no paste is left on the skin. Discard any leftover paste and water rather than keeping it, and wash the pan and strainer straight away. Discontinue use if irritation occurs.

Choosing a base

Gram flour is the base named in the product guidance and the one most households reach for. It thickens the avarampoo water into a paste that holds on the skin, and it rinses off with plain water.

Any other suitable natural base you already use can take its place. If you are also using vettiver powder, the two are commonly combined — the avarampoo and vettiver bath preparation gives the proportions. Whatever you choose, patch test in that base, since a different base is a different preparation.

Getting the consistency right

The most common mistake is pouring in all the water at once. Gram flour goes from stiff to runny very quickly, and a thin paste slides off the skin before it has been spread. Add the water by the spoonful and stop early — it is easier to loosen a thick paste than to rescue a thin one.

Too thick and dragging: add another spoonful of the avarampoo water.
Too runny: stir in a little more gram flour.
Lumpy: keep stirring for a minute, or press the lumps against the side of the bowl with the back of a spoon.
Warm to the touch: wait — the water was not fully cooled.

Common mistakes

Soaking the flowers in cold water instead of boiling them releases very little, which is why the method starts with a pan. Grinding the dried flowers and stirring them straight into gram flour skips the same step.

Making a large batch of the water to use over several days is the other one. The preparation is made fresh for a single use, and the flowers are best kept dry and sealed in their pack until then — the ingredient page covers storage.

Key takeaways

Boil the flowers first — the cooled, strained water is what gets mixed, not the flowers.
Add the water to gram flour a spoonful at a time and stop before the paste turns runny.
Patch test before first use, keep clear of the eyes and rinse before the paste dries hard.
Make it fresh for a single use and discard what is left over.

Frequently asked questions

How many flowers should I use?

A handful, as the product guidance says. Boiled in about two cups of water, that is a reasonable starting point for a single use — adjust once you know how much paste you need.

How long should I boil the flowers?

A few minutes, then take the pan off the heat and let the water cool. There is no need for a long simmer.

Can I use the water without gram flour?

The product guidance describes mixing the strained water with gram flour or another suitable natural base. If you prefer a different base, use one you already know and patch test with it.

Can I keep the leftover water or paste for tomorrow?

No. Prepare only what you need for a single use and discard the rest. Boil a fresh handful of flowers next time.

Can I use it on my face?

The product guidance describes it as a traditional body or face preparation. Patch test first, keep the paste well away from the eyes and discontinue use if irritation occurs.

Should I grind the flowers into a powder?

No. The flowers are sold whole so that they can be boiled — grinding them and mixing the powder straight into a base skips the step the method depends on.

What this page is based on

THENVANAM product specification — THENVANAM Sourcing
Composition, net quantity, SKU and usage guidance are taken from the current product specification for each pack.
Documented South Indian household practice — THENVANAM Editorial
Descriptions of traditional use record how an ingredient has customarily been prepared and used. They are not statements of clinical effect and should not be read as health advice.

About the author

THENVANAM Editorial · Product and content team

The THENVANAM editorial team documents what each botanical is, which part of the plant is used, and how it has traditionally been prepared in South Indian households. We describe traditional practice and product composition — we do not offer medical advice.